How to Remove a Tub Drain Stopper

My husband refuses to help me install a new basement laundry sink. To make it easy I have found a location immediately adjacent to a vertical plastic plumbing stack. Surely it can’t be that hard to cut into the pipe and install the necessary fittings. What is involved and what do I need to do to make sure the work meets the plumbing code? What a shame your husband is not a team player. I wonder if he is intimidated by the project.

Installing A New Bathtub Step By Step

The old tub will be removed, along with the row of tile if applicable that adjoins it on the walls. Because the new walk-in tub is likely to be much deeper, or higher, than the old tub, you will likely need to retile or replace the walls of the tub area as well, particularly if you plan on using the tub as a shower as well. This is because the motor will need to be set nearby, as well as hooked up properly.

Most baths easily retrofit into the space already occupied by an alcove tub, so no major remodeling is necessary beyond reconfiguring the stall.

The Flojet DC portable waste pump is the ideal solution for emptying holding tanks on recreational vehicles and avoiding dump stations.

As well, it gives you a chance to clean out the shell of the hot tub and the front ends of your jets. How tub water can last between 3 to 4 months, after which non-organic contaminants, such as sun block or lotion, and salt from perspiration all known as Total Dissolved Solids can make your hot tub water cloudy and begin to cause chemical imbalances. It may be to prepare for the winter or just flush out the system in the summer, but either way, draining your hot tub should happen once every 3 to 4 months, so you should know how to properly drain your hot tub.

It is recommended to use a submersible pump to help push out the water from the hot tub. The steps continuing, are for a garden hose. Remove the front panel of your hot tub and locate the hose spigot.

plumbing drain for bathtub on concrete slab

Edit Answer for another minute The drain connection is commonly moved from near the faucet wall of the area to near the center though there are left and right drain configurations designed to use existing tub drain location, if fits with your configuration – so the concrete slab has to be cut, the drain pipe extended to there, and turned up to connect to the drain piping, then the excavated slot backfilled with coarse sand, then the concrete slot concreted back in.

Not terribly hard in most cases but time consumingand cramped quarters so costs more than just running a pipe extension in a wood subfloor. Curbless showers, especially if they do not have a glass partition and door that goes essentially to the floor, generally require a waterproof bathroom floor for at least 3 feet or more from the shower more like 6 feet or more plus waterproof walls if one of those silly no partition at all ones, sloping towards the shower for drainage.

WE•Stand. With increasing demand, shrinking supplies, reduced quality and reliability, constrained infrastructure, climate change, and pervasive droughts throughout the world, there is a critical need to reduce water consumption attributed to the built environment through conservation and reuse.

March 4, Background: I have a ‘s ranch home that I’ve been busy updating. I finally got around to looking at a “stinky” closet that we assumed was ammonia from cat urine the prior owners let the cat sleep in there. Anyways, I discovered this weekend that it’s actually coming from our guest bath. The closet has an access panel in it, and after I pried it off I discovered a lovely petri dish underneath and it was very humid inside.

The prior owners had zero caulk around the tub rim which I took care of several months ago when we moved in. I ran the tub and shower and can’t seem to find any leaks Research online tells me that this was normal when they poured foundations to allow for the plumber to install the tub later.

Plumbing Supplies > Drains & Drain Fittings > Tub & Shower Drains

Click here for larger image A bathtub drain flange is the finished drain part in the tub that is visible to users. Some manufacturers refer to the drain flange as a “drain body” or “drain basket”. Drain flanges come in many different finishes and have a variety of stopper options. The drain flange is threaded into a piece called a drain shoe. Underneath the tub drain flange will be a good amount of plumber’s putty to seal the inside of the tub drain, and a rubber gasket underneath the tub to seal the drain flange to the tub.

The Onyx Collection manufactures shower bases, shower pans, tub replacements, lavatories, tub surrounds, fireplace hearths, slabs, seats, trim and other shower accessories to your specifications in almost any size, shape, and color, for your new or remodeled bathroom needs.

If you have any misgivings about doing it, hire a plumber who has the experience to install it and the license to hook up the fixtures. Placing the ledger board The first step in installing a tub is to set in place a ledger board that supports the edges of the tub that contact the walls of the tub enclosure. Push the tub into the enclosure and mark the top of the flange on the wall studs with a pencil. Measure and mark the location for the top of the ledger, usually about 1 inch below the first mark.

Use coarse drywall screws to fasten the ledger board horizontally and level across the back wall of the alcove. Fasten shorter ledger boards to the ends of the enclosure, level with the board you install on the back wall.

ShowerLine

Since there are so many variations to the plumbing set- up and tub type, there is a wide variety of clawfoot tub faucet styles. You want to be sure the one you purchase will suit your needs and your tub. Here’s a look at what’s available: A tub- filler is a faucet that does not have any shower connections. It is simply used to fill your tub.

These faucets are connected to a handheld shower.

Dec 31,  · Best Answer: Usually your concrete floor will have a 12″ square open area underneath your tub where the drain pipe comes up. This is so you have access to the trap, which is below floor level, and to give you room to adjust the position of the drain pipe so that it lines up with the : Resolved.

Finally, though, the time had come to finish the job. But there was a problem which came in two parts. The pretty chrome water inlet standpipes that came with the tub were going to be a challenge when it came to making the final connections. No flex to them at all, and thus no margin for error. Unforgiving to the max. In order to make the maximum use of available space, the tub was being installed crosswise near the far end of the bathroom. There was not enough room to get all of me down on the far side, so that hot water hookup would have to be made in extremely tight circumstances.

No idea how I managed that, then or now, but I was not particularly upset. Now I could go to town and find flex-pipe connectors. That really made more sense anyway.

Disassembling Pop

Step 1 Position the Tub Work the tub into place. Be careful not to damage the drain when repositioning the tub. Check to make sure that the drain lines up properly into the hole. Step 2 secure tub with adhesive under support blocks Secure the Tub To secure the tub in place, lift the front end of the tub just enough to allow you to apply some construction adhesive under the front support blocks.

The old installation had the drain line entering the top of the cabinet to go to the sink drain. But with the new dishwasher this pinches the drain line behind the machine. I am thinking of drilling a new hole at the bottom of the cabinet, where the dishwasher won’t pinch it, then I .

A tub is large and heavy and bathrooms may be awkward in shape and are not usually all that large, which can make removing an old tub and installing a new one a real challenge. However, bathtubs can get worn over time and need replacing. You will need help for this project to move the tub. Steps Measuring the Bathroom Space 1 Ensure the new bathtub will fit in the space. Measure the old bathtub and the doorway. Sometimes in the construction of a house, the bathtub was placed in the bathroom before the walls were completed, causing a problem when you need to remove it.

Make sure you can get the old one out and the new one in. If the new tub is not exactly the same as the old one, you will have to modify the plumbing later. Part 2 Removing the Old Bathtub 1 Turn off the water supply and drain the water supply lines by opening a faucet below the level of the bath.

Residential Water Softener Drain installation tips

Next If you’re trying to clean your bathtub drain of clogged hair and your drain is covered by a tub drain stopper, you’re probably getting frustrated. Tub drain stoppers are difficult pieces to remove and WD won’t help ease open any screws. Plumbers have specialized tools to remove the drain stopper, but if you want to do it yourself, there’s a makeshift way [source: Read the steps listed below and learn about how you can remove a tub drain stopper yourself.

All you need are slipknot pliers and a sturdy screwdriver. Here’s what to do:

Bathroom Shower and Bathtub Installation and Plumbing. Shower drains; A standalone shower can greatly enhance the beauty of your bathroom. Our professional installation process makes remodeling your shower easy, convenient, and affordable, and our installers and plumbers deliver professional and courteous service every step of the way.

Trip Lever Identify which stopper you have: These are generally the easiest kind to remove or replace since they do not need the removal of the trip lever. The stopper opens and closes with the push of your toe. The stopper has a knob in the center and you must push it down to close and pull it up to open.

This looks very similar to the Push-Pull style, but you will need to lift and turn the stopper in opposite directions to open and close. This stopper uses a toggle that when flipped from side to side, will open or close. This style can have a Trip Lever or Turn Style mechanism on the overflow that moves an internal push rod against a rocker arm attached to the stopper to raise or lower the stopper.

Pop-Ups have a visible stopper in the tub drain, and cannot be covered by a strainer. Trip Lever or Turn Style: These two styles use an internal plunger to stop water flow. When the overflow plate is activated by tripping a lever or turning the plate it causes the plunger to raise or lower. Trip Lever and Turn Style assemblies normally do not have a visible stopper in the tub drain.

Bathtub Plumbing – New Installation